SISTEM PENGHITUNG PUSH UP OTOMATIS MENGGUNAKAN MIKROKONTROLER DI RIYADH GYM FITNESS CENTER

Penulis

  • Nurul Hamdi Universitas Ubudiyah Indonesia
  • Herawati Herawati
  • Putri Fazlina
  • Pardi Pardi
  • Periskila Dina Kali Kulla

DOI:

https://doi.org/10.33143/jics.v10i2.4599

Abstrak

Abstrak— Kesehatan dan kebugaran fisik merupakan aspek penting dalam menjaga kualitas kehidupan seseorang. Salah satu yang umum dilakukan untuk menjaga kebugaran adalah Latihan push-up, namun pada saat melakukan push-up sering kali lupa pada repitisi yang telah dihitung karena terlalu focus pada Latihan push-up. Oleh karena itu penelitian ini dilakukan untuk merancang sistem penghitung push-up otomatis menggunakan mikrokontroler di Riyadh Gym Fitness Center. Metode penelitian yang digunakan adalah metode kuantitatif eksperimen. Berdasarkan hasil penelitian ini dapat disimpulkan bahwa sistem  rancangan ini selain dapat menghitung jumlah repitisi juga dapat melihat jarak pada masing-masing push-up yang real-time.

 

Kata Kunci: Sistem Penghitung Otomatis, Push-up, dan Mikrokontoler

 

Abstract— Health and physical fitness are important aspects in maintaining quality someone's life. One thing that is commonly done to maintain fitness is push-up exercises, but when doing push-ups you often forget to do the repetitions it was calculated because he was too focused on the push-up exercise. Therefore, this research was carried out to design an automatic push-up counting system using a microcontroller in Riyadh Gym fitness Center. The research method used is experimental quantitative methods. Based on the results of this research, it can be concluded that this design system Apart from being able to count the number of repetitions, you can also see the real-time distance of each pushup.

Keywords: Automatic Counter System, Push-up, and Microcontroller

Referensi

Abitta, N. M. (2021). Sistem Pengaturan Lalu Lintas Yang Terintegrasi Menggunakan Sensor Proximity Berbasis Mikrokontroler (Tugas Akhir). Universitas Diponegoro, Semarang.

Alhaq, M. (2022). Perancangan Pengamanan Sepeda Motor Berbasis Arduino Uno Dengan Metode Radio Frequency Identification (Rfid) Menggunakan E-Ktp (Tugas Akhir). Universitas Ubudiyah Indonesia. Banda Aceh.

Alhaq, M. (2022). Perancangan Pengamanan Sepeda Motor Berbasis Arduino Uno Dengan Metode Radio Frequency Identification (Rfid) Menggunakan E-Ktp.

Amari, R. O. (2023). Sistem Kontrol Nyala Lampu Otomatis Dengan Menggunakan Sensor Gerak Pada Ruang Kamar Mandi Berbasis Microwave (Radar). 31–41.

Andika, R. (2022). Monitoring Detak Jantung Dan Kadar Oksigen Pasien Pada Rumah Sakit Rsud Dr. H. Yulidin Away Tapaktuan Berbasis Iot. 32.

Dadi Riskiono, S., Septiawan, D., & Setiawan, R. (2018). Implementasi Sensor Pir Sebagai Alat Peringatan Pengendara Terhadap Penyeberang Jalan Raya. 8(1).

Dimas Ade Putra. (2023). Alat Penghitung Jumlah Gerakan Pull Updan Push Up Menggunakan Sudutkemiringan Pada Sensor Mpu6050 Berbasisinternet Of Things. 8, 1–10. https://doi.org/10.30865/Mib.V8i1.6937

Erwins. (2024). Sejarah Mikrokontroler. Retrieved June 2024, from https://Erwins.Teachable.Com/ Courses/775238/Lectures/14057657

Lailatul Mufidah, K. T. (2021). Sistem Pengaturan Lalu Lintas Yang Terintegrasi Menggunakan Sensor Proximity Berbasis Mikrokontroler. 7(3), 6.

Mauliddiyah, N. L. (2021). Pengaruh Latihan Push Up Terhadap Prestasi Tolak Peluru Pada Siswa Kelas Ii Sma Negeri 11 Blang Cut Tahun Pelajaran 2020/2021. 3(1), 6.

Putra, D. A., Jufrizel J., Ullah, A., & Maria, P. S. (2024). Alat Penghitung Jumlah Gerakan Pull Updan Push Up Menggunakan Sudut Kemiringan Pada Sensor Mpu6050 Berbasisinternet Of Things. Jurnal Media Informatika Budidarma, Vol. 7.

Rahmad, M. (2016). Perancangan Prototype Lampu Otomatisberbasis Sensor Pir Dan Mikrokontrolerarduino Uno. 1–58.

Stmicroelectronics. (2022). Vl53l0x Datasheet. 1–38.

Suharjana, S. (2015). Analisis Program Kebugaran Jasmani Pada Pusat-Pusat Kebugaran Jasmani di Yogyakarta. Medikora, 11(2), 135–149.https://doi.org/10.21831/Medikora.V11i2.2813

Unduhan

Diterbitkan

2025-02-04

Terbitan

Vol 10 No 2 (2024): OKTOBER 2024

Bagian

Articles

Lisensi

COPYRIGHT TRANSFER FORM

The copyright to this article is transferred to Universitas Ubudiyah Indonesia (UUI) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UUI. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.

We declare that:

  1. This paper has not been published in the same form elsewhere.
  2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
  3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.

Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UUI. The copyright transfer covers the right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature. The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.

Retained Rights/Terms and Conditions

  1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the work.
  2. Authors may reproduce or authorize others to reproduce the work or derivative works for the author’s personal use or for company use, provided that the source and the UUI copyright notice are indicated, the copies are not used in any way that implies UUI endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
  3. Although authors are permitted to re-use all or portions of the work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.